Professional Counter Surveillance Probe and Monitor Kit
Home > Corporate Security > Camera and Tap Detectors (Professional Counter Surveillance Probe and Monitor Kit)
|
|
Perform complete sweeps without perform sweeps the need to bring in an outside TSCM specialist.
Revolutionary Two-In-One Camera Detector Finds Both Wired & Wireless Cameras Easily Find Hidden Cameras w/ This Easy-To-Use Device Trusted By Private Investigators Worldwide This kit is best utilized by passing the RF probe around the surfaces of area being checked, but doing so at a very slow and steady rate, and no faster than that you would use to lay down a coat of latex paint with a four inch paint brush. The Magnetic and Infrared probes are used in a similar manner. With the VLF probe you can test all electrical outlets for carrier current covert eavesdropping devices. It can also detect and locate RF tracking transmitters which may have been installed to follow vehicles. The Acoustic Leakage Probe can be used to test both sides of walls, pipes, air ducts, and other locations where sound could leak from the area being checked and monitored by an eavesdropper with the naked ear. The Acoustic Leakage Probe, ALP700 probe also assists in the placement of acoustic noise generators and audio jammers. Additionally, it can also be used as an automatic monitor mode once a sweep has been conducted to detect and alarm on any changes while one is away. The line probe can be plugged into the auxiliary output and used to check any unknown wires and to test for possible eavesdropping activities and/or devices. The 24-hour recorder output and controls will store suspicious sounds on a standard cassette recorder (not included) while you are away. Features:
Multi-Functional Utility The CPM700 comes with probes to detect RF transmitters (audio and video), carrier current transmitters, and telephone bugs. Probes are also available to detect infrared transmitters, tape recorders, and acoustic leakage. Wideband Coverage Full spectrum coverage from 200 Hz to over 3 GHz including infrared signals. Monitor Mode After a sweep, the alarm monitor (silent or audible alert) guards against new devices brought in or the remote control activation of surveillance devices. Auxiliary Audio Input Allows user to listen to telephones or lines for hot mikes, hook switch bypass infinity transmitters and other telephone bugs. Unknown wires and cables can be tested for wired microphones. FILTER:? Audio filter used to accentuate voice frequencies and remove noise. MODE:? Sets the unit to Search or Monitor function. Search is for performing a sweep with the audio Automatic Gain Control engaged, the Monitor Mode sets the Alarm and Record output to detect an intrusion. ALERT:? Selects either audible Tone beeper or Silent flashing LED output from Monitor Mode. LOW BATTERY INDICATOR:? Voltage indicator indicates approximately 10% remaining power. STATUS DISPLAY:? Shows unit operating conditions made by button selections. GAIN:? Adjusts the internal sensitivity of the Detector and Audio systems. PROBE INPUT:? Provides input and power for active probes and automatically selects the appropriate Probe or Auxiliary detector circuits. PULSING SEGMENT:? Indicates alarm trip point in the Monitor Mode and activates the Alarm and Remote output. INPUT LEVEL:? Bar graph indicates signal strength of Probe or Auxiliary inputs. ALERT LED:? Flashes Red when input level exceeds trip point of Monitor Mode. THRESHOLD:? Sets the trip point for the Monitor Mode. GAIN:? Controls the audio gain (volume) to the speaker or headphone output. PHONES:? Allow for silent headphone detection, disconnects the internal speaker. SPECIFICATIONS: RF PROBE Gain: 20 dB nominal Frequency Response: 200 Hz - 3 GHz, optional BMP-1200 probe extends this from 200 Hz to 12 GHz Sensitivity: -62 dBm (1 segment) Sensitivity: -85 dBm M.D.L. VLF PROBE Frequency Response: 15 kHz - 1 MHz, -3 dB Maximum Input Voltage: 300 VAC 50-60 Hz Isolation: 500 VAC 60Hz Sensitivity: -38 dBm (1 segment) Sensitivity: -60 dBm M.D.L. AUDIO AMPLIFIER Input Impedance: 50K Ohm balanced Input Range: 1.7 uV - 10V (135 dB) AGC Dynamic Range: 100 dB (high and low gain) Frequency Response: 100 Hz - 15 kHz +/- 3 dB (filtered) 500 Hz -24 dB/octave, 2.5 kHz - 18 dB/octave Headphone Output: 5V p-p, 220 Ohms Record Out: 25 mV p-p nominal with AGC DISPLAY 18 segment LCD bar graph with pulsing single segment trip point 50 dB dynamic range (1 segment High Gain to MAX Low Gain) Alert Output: 2.8 kHz tone or silent red LED at 2 Hz Remote Output: Normally Open (N.O.) contact (300 mA 25V MAX) BATTERY 8 ea. MN1500 AA Alkaline, Life 10-16 hrs 8 ea. 550mAh Nickel Cadmium (NiCd), estimated life in 3-5 hrs per charge (Optional) Low Battery Indicator approximately 10% remaining power AC ADAPTER and CHARGER Input: 95-130 VAC 50-60 Hz, or 200-275 VAC 50-60 Hz Output: 12 VDC with 500 mA Nickel Cadmium (NiCd) Recharge Time: 8-10 hrs BASIC CPM-700 UNIT Size: 9 1/8 x 6 1/8 x 1 3/4 in, 23.2 x 15.6 x 4.4 cm Weight: 39 oz, 1.1 kg CARRY CASE WITH ALL STANDARD ITEMS Size: 16 3/8 x 11 1/4 x 3 in, 41.6 x 28.6 x 7.6 cm Weight: 7 lbs, 3.18 kg Specifications:
Includes:
Size:
On Sale |